Ca-Mg-Al复合氧化物催化尿素与1,2-丙二醇制碳酸丙烯酯

采用共沉淀法制备了系列Ca-Mg-Al复合氧化物催化剂，通过对沉淀剂配比、沉淀液pH值及焙烧温度等制备条件的考察，得到以Na₂CO₃为沉淀剂、pH=9.5、850℃下焙烧4h制备的Ca-Mg-Al催化活性最高。在 n(PG)∶n(urea)=1.5∶1、反应温度为145℃、绝压20kPa、反应时间4h、催化剂用量为尿素质量的5%时，碳酸丙烯酯收率达到84.6%。采用XRF、XRD、NH₃-TPD、SEM及BET对催化剂的组成、晶型及酸性进行了表征，发现随着沉淀剂中Na₂CO₃的含量增加，催化剂中CaO∶MgO的比例增大，碳酸丙烯酯的收率亦升高；经850℃焙烧后，催化剂中存在CaO和MgO两种活性中心，起协同催化作用；随着焙烧温度由700℃升高到850℃，NH₃-TPD脱附曲线向低温方向偏移，且强酸中心NH₃脱附峰面积比由81.14%明显下降为0，中强酸中心NH₃脱附峰面积比由0增加到78.07%，而碳酸丙烯酯收率由68%增加到84.6%，这表明催化剂强酸性位的减少是催化活性增加的主要原因。     

餐饮废油生物柴油低温流动性的改进研究

使用气-质联用仪测定餐饮废油生物柴油(WCME)和-10号柴油(-10PD)的组成,使用冷滤点试验器和运动黏度试验器测定WCME的低温流动性,同时使用调合、添加低温流动性改进剂的方法改进WCME的低温流动性。实验结果表明,WCME主要由饱和脂肪酸甲酯和不饱和脂肪酸甲酯组成,质量分数分别为27.63%和71.81%;WCME冷滤点为0℃,运动黏度(40℃)为4.41mm2/s;WCME与-10PD调合后,冷滤点降低,其中B20的冷滤点最低,为-13℃,运动黏度随着WCME的体积分数的减少,逐渐接近-10PD的运动黏度。通过添加低温流动性改进剂,WCME,B10,B20的冷滤点分别从0,-8,-13℃降至-4,-26,-25℃。     

应急避难场所广播设计实现

应急避难场所广播体系由应急广播、场所广播室、接收端、网络接收、广播管理群、监测系统等6部分组成.针对电台在市区建立应急避难场所广播作出设计,在学校、社区、广场上安装广播系统,做到市区全方面覆盖.     

Electrospun microporous gelatin–polycaprolactone blend tubular scaffold as a potential vascular biomaterial

The work reported involved the fabrication of an electrospun tubular conduit of a gelatin and polycaprolactone (PCL) blend as an adventitia‐equivalent construct. Gelatin was included as the matrix for increased biocompatibility with the addition of PCL for durability. This is contrary to most of the literature available for biomaterials based on blends of gelatin and PCL where PCL is the major matrix. The work includes the assiduous selection of key electrospinning parameters to obtain smooth bead‐free fibres with a narrow distribution of pore size and fibre diameter. Few reports elucidate the optimization of all electrospinning parameters to fabricate tubular conduits with a focus on obtaining homogeneous pores and fibres. This stepwise investigation would be unique for the fabrication of gelatin–PCL electrospun tubular constructs. The fabricated microfibrous gelatin–PCL constructs had pores of size ca 50–100 μm reportedly conducive for cell infiltration. The measured value of surface roughness of 57.99 ± 17.4 nm is reported to be favourable for protein adhesion and cell adhesion. The elastic modulus was observed to be similar to that of the tunica adventitia of the native artery. Preliminary in vitro and in vivo biocompatibility tests suggest safe applicability as a biomaterial. Minimal cytotoxicity was observed using MTT assay. Subcutaneous implantation of the scaffold demonstrated acute inflammation which decreased by day 15. The findings of this study could enable the fabrication of smooth bead‐free microfibrous gelatin–PCL tubular construct as viable biomaterial which can be included in a bilayer or a trilayer scaffold for vascular tissue engineering. © 2019 Society of Chemical Industry     

副井信号操车设备远程控制设计与应用

副井信号操车设备远程控制系统是数字化矿山建设的重要组成部分，此系统应用计算机网络技术、可编程控制器技术、无线通信技术、传感器检测技术和视频监控技术，以总线冗余、Profibus-DP现场总线控制和工业以太网为基础组成的数字化网络控制系统。通过将原系统分段独立的控制方式改造成集中遥控和远程操作的方式来减少副井提升机各中段水平的岗位操作人员数量、提高设备的安全性和生产效率，适用于地下矿山企业的长期生产工况作业，是智慧化矿山建设的必然趋势。     

Isolation of antimicrobial agent from the marine algae Cystoseira hakodatensis

Cystoseira hakodatensis is an unutilised brown algae belonging to family Sargassaceae. A crude methanol extract from the algae showed inhibitory effects on the growths of Bacillus cereus and Bacillus licheniformis. To isolate the major antimicrobial agent, a sequential active‐guided isolation procedure was applied: liquid–liquid extraction, column chromatography and bio‐autography. A marked antimicrobial agent (active α) was isolated in hydrophobic fraction and was determined to phenolics without carbohydrates and proteins by phytochemical test. Regarding the antimicrobial potential, the isolated active α showed better inhibitory effects against B. cereus and B. licheniformis at 2 and 4 times of lower concentrations (62.5 and 31.3 μg mL^?1) in comparison with epigallocatechin gallate. These results showed that C. hakodatensis is a potential source of antimicrobial agent capable of preventing the growth of the two bacteria.     

Measurement of solubility and diffusion coefficients of ethylene in solid and molten low-density polyethylene with different melt indices

The diffusion behavior of ethylene in polyethylene is of great importance for the polymerization and degassing of polyethylene (PE) industry. Based on the gravimetric sorption and desorption measurement approach, an intelligent gravimetric analyzer is applied to obtain the solubility and diffusion coefficients of ethylene in solid low-density PE (LDPE) with different melt indices at 30°C to 70°C, 0 to 4 atm and in molten LDPE at 160°C to 230°C, 0 to 4 atm, respectively. Results indicate that both the solubility and diffusion coefficients of ethylene in solid LDPE are smaller than those in molten LDPE, while the dissolution enthalpy and diffusion activation energy of ethylene in solid LDPE are higher. In addition, one- and two-dimensional diffusion models are built and the effects of particle size, polymer properties, and operation conditions are systematically investigated on the diffusion behaviors of ethylene in solid and molten LDPE.